N536BS-CC1312R PA Module, +33dBm
- Detail
- Parameters
N536BS integrated TI CC1312R, PA and LNA chip, suitable for 169, 433M, 868MHz and 915M band.
Maximum output power is 33dBm. CC1312R module has the characteristics of low cost, low power consumption and small size. The module is designed with 4-layer board, with excellent impedance matching and anti-interference. The module is mainly for IoT, intelligent home, wireless meter reading, scientific research and medical treatment, and medium and long-distance wireless communication equipment. N536BS leads all pins out for secondary development.
Radio module CC1312R module up to 33dbm outpower and down to -112dbm sensitivity.
ISM Frequency supported by N536BS module
169M band: 160 MHz to 175 MHz (China)
433M band: 410 MHz to 510 MHz (China)
770M band: 770 MHz to 780 MHz (China)
868M band: 868 MHz to 870 MHz (China, EU, USA)
888 MHz to 889 MHz (Australia)
915M band: 902 MHz to 930 MHz (USA)
N536BS module Parameters
| RF Interface | Parameter | Introduce |
| Frequency | 169M, 433M, 868M, 915M, 1200MHz | Support ISM |
| Output Power | +33dBm | The maximum power 500mW |
| Sensitivity | -112dBm | 50kbps |
| Symbol Rate | 0.3-4000kbps | Software programming control |
| Deviation | +/-10kHz | Antenna interface |
| Distance | 8000m | In clear and open environment, the antenna gain is 3 dBi, the height above the ground is 2.5 meters, and the air speed is 1.2 kbps. |
| Hardware parameters | Value | Remarks |
| Size | 36 x 24 x 3mm | - |
| Antenna Interface | IPEX, stamp hole | - |
| Communication Interface | UART, SPI | Software programming |
| Package | SMD | - |
| Electrical Parameters | Minimum | Typical | Maximum | Remarks |
| Volt | 1.8V | 3.3V | 3.9V | |
| PA Volt | 4.5V | 5V | 5.5V | |
| Emission Current | 1200mA | Instantaneous power consumption | ||
| Receiving Current | 10mA | - | ||
| Sleep current | 1uA | Software programming control | ||
| Working Temperature | -30℃ | 75℃ | - |
N536BS control Logic
N536BS Pinout Description
Pin Number | Function | Describe |
1 | GND | |
2 | GND | |
3 | VCCPA | PA power supply, 4.5V -- 5.5V, MAX current: 1200mA |
4 | VCCPA | PA power supply, 4.5V -- 5.5V, MAX current: 1200mA |
5 | GND | GND |
6 | DIO2 | MCU IO port |
7 | DIO3 | MCU IO port |
8 | DIO5 | MCU IO port |
9 | DIO6 | MCU IO port |
10 | DIO7 | MCU IO port |
11 | DIO8 | MCU IO port |
12 | DIO9 | MCU IO port |
13 | DIO10 | MCU IO port |
14 | VCC | CC1314R10 power supply, 2V -- 3.6V |
15 | GND | GND |
16 | DIO11 | TMS |
17 | DIO12 | TCK |
18 | DIO13 | MCU IO port |
19 | DIO14 | MCU IO port |
20 | DIO15 | MCU IO port |
21 | TMS | MCU IO port |
22 | TCK | MCU IO port |
23 | RESET | MCU IO port |
24 | DIO16 | MCU IO port |
25 | DIO17 | MCU IO port |
26 | DIO18 | MCU IO port |
27 | DIO19 | MCU IO port |
28 | DIO20 | MCU IO port |
29 | DIO21 | MCU IO port |
30 | DIO22 | MCU IO port |
31 | DIO23 | MCU IO port |
32 | DIO24 | MCU IO port |
33 | DIO25 | MCU IO port |
34 | GND | |
35 | RF |
N536BS Pinout Description
Ordering information
N536BS-CC1312R-169M CC1312R+PA 160-175MHz +33dBm
N536BS-CC1312R-433M CC1312R+PA 410-510MHz +33dBm
N536BS-CC1312R-868M CC1312R+PA 860-880MHz +33dBm
N536BS-CC1312R-915M CC1312R+PA 910-930MHz +33dBm
Download
Test method of N536BS module
Take the supporting base plate of Heyan technology as an example:
The bottom board of N536BS is T532AP, which integrates USB to serial chip, led, button, burning port and module card port. As shown in the figure:
N536BS secondary development method:
The CC1312R module is stuck on the backplane as shown in the figure, and the IPEX is connected with the antenna. The burning port is connected with xds110 according to the silk screen printing, and then online simulation can be carried out to test the performance of the module.
Module Programming
The schematic diagram of the module base plate can be obtained from our official website.
Please contact us for specific programming information or download it from TI official website www.ti.com.